Veteran Garage Door Repair | Keller TX | 817-769-8488

Veteran Garage Door Repair | Keller TX | 817-769-8488

Garage Door Opener Repair

You might find that your garage door opener has been offering you issues, so you need to repair it. You can fix it by changing a circuit board, a photo-eye sensor, the major drive gear, or the set-limit switches. You can also check if the safety and security sensing units are functioning appropriately.

Changing a circuit board

Replacing a motherboard for your garage door opener calls for a couple of steps and also devices. First, you need to switch off the circuit breaker and also disconnect any kind of wires. Next off, open up the motherboard cover. This will help you to identify the issue and also establish if you need a brand-new board. Next, eliminate the old board and also its cord adapters.

You can after that proceed to replace the motherboard. The substitute process is very easy and also takes about 10 minutes. A brand-new circuit card will set you back concerning $80. To shield your new circuit board from power surges, you can acquire a rise guard.

Changing a photo-eye sensor

Changing a photo-eye sensing unit can be a rather straightforward task. Initially, remove the sensing unit from the door and also make certain it is located properly. If the sensing unit is angled by any means, it might not be obtaining the right signal, which can be causing the blinking lights. If you observe that the photo-eyes are out of alignment, you may need to have a specialist come and repair the trouble.

The photo-eye sensor consists of two items that place outside of the door tracks and towards the flooring. The picture eyes will certainly have a small LED light as well as should be solid in color. If the light is blinking, its likely the photo-eye is malfunctioning and will certainly require to be replaced.

Replacing a primary drive equipment

To replace a garage door opener main drive equipment, begin by removing the cap from the chain pulley-block. Next, get rid of both screws holding the drive equipment to the gear assembly. Currently, you can unfasten the 3 stress pins. Squeeze them from both sides and after that remove them. After that, separate the 3 cables from the garage door opener motor. These cords ought to be white, red, as well as blue.

As soon as you have actually gotten rid of the old equipment, set up a new one. Make certain to oil it well. Put the new equipment into the shaft, making certain to line up the mounting openings. Make sure the equipment and also sprocket assembly are located correctly to ensure smooth operation. Next, use a hammer and also a nail to drive a pin right into the brand-new gear.

Readjusting the set-limit buttons

The initial thing you must do if your garage door is not working correctly is to examine the set-limit switches. You may need to readjust them to make sure that the door closes earlier or stops prior to it reaches the floor. You can inspect this by checking out your garage doors manual or online.

To change the set-limit switches, youll require a screwdriver or socket. Change the handle clockwise or counterclockwise until the door moves up and also stops, or reduces its distance. To check for appropriate traveling range, measure the space from all-time low of the garage door to the ground.

Veteran Garage Door Repair – Keller

204 S Main St Ste 105, Keller, TX 76248, USA

817-769-8488

https://veterangaragedoor.com/veteran-garage-door-repair-of-keller-tx/


Garage Door Repair


Garage Door Installation


Garage Door Company


Garage Door Service


Garage Door Opener Repair

Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair

204 S Main St Ste 105
Keller,TX
76248
817-769-8488

Leave a Reply

Your email address will not be published. Required fields are marked *


Back To Top